In stock
Bathroom lighting
IP44 bathroom wall lights, ceiling lights and illuminated mirrors matched to the BS 7671 zones. Free delivery in the UK and the European Union. Buying guide
Products
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
In stock
This page helps you choose a bathroom light: IP rating, mirror lighting and general light. In a 5 m² bathroom with the bath at the far end and the basin 1 m from its edge, the mirror falls outside the zones, so IP44 is advised; above the bath, IPX4; at the mirror, two 4,000 K wall lights.
The BS 7671 zones set the IP rating
- Zone 0 is the inside of the bath or shower tray. Only IPX7 fittings on 12 V SELV.
- Zone 1 runs above the bath or tray up to 2.25 m from the floor. IPX4 minimum, IPX5 where water jets are used for cleaning. Higher up, directly over the bath, we still recommend IPX4.
- Zone 2 covers the 60 cm around zone 1. IPX4 minimum.
- Outside the zones, no IP rating is required. IP20 is allowed, IP44 advised because of steam.
The basin creates no zone of its own. Only the distance to the bath or shower counts, measured from the edge of the bath or tray. With a walk-in shower and no tray, zone 1 reaches 1.20 m from the fixed shower head; we keep another 60 cm in reserve as if zone 2 applied. Every bathroom circuit needs 30 mA RCD protection, and in England and Wales work within the zones falls under Part P.
What IP rating do bathroom lights need?
IPX4 is the minimum in zones 1 and 2; outside the zones, no IP rating is required, though IP44 is advised because of steam. Nine fittings in ten on this page are IP44, which covers zones 1 and 2 away from direct jets.
Can you hang a chandelier in a bathroom?
Yes, outside the shower and bath zones, in the centre of the room or above the basin if the ceiling is high enough, ideally rated IP44 in a steamy room. This category includes chrome chandeliers with crystal drops and IP44 glass pendants made for bathrooms; if you are unsure about a zone, have an electrician confirm the position.
At the mirror, two wall lights at eye level
Wall lights make up two-thirds of the section: cones, tulips and opal glass globes on chrome, or bars of 50 to 80 cm to go above the mirror. Bathroom wall lights have their own section, and illuminated mirrors build the light into the glass.
What height should bathroom mirror lights be fitted at?
Either side of your face, fit the wall lights 1.55 to 1.65 m from the floor; above the mirror, a strip light goes at 1.90 to 2.00 m. At the sides, two sources of 500 to 800 lumens keep shadows soft. Above, a strip light needs 800 to 1,200.
What colour temperature is best for a bathroom mirror light?
Take 4,000 K and a CRI of at least 90 for shaving or make-up. The catch on this page: almost every fitting that states its colour temperature is warm white, 3,000 K at most, which gives skin a yellow cast; with a G9 or E14 lampholder, you simply fit the 4,000 K bulb you want.
For general bathroom lighting, an IP44 ceiling light
Fitted more than 60 cm from the edge of the bath or tray, the ceiling light is outside the zones and IP44 is enough. Closer, or directly over the bath even on the ceiling, it needs IPX4. The few recessed fittings are under bathroom spotlights.
How many lumens does a bathroom need?
Allow 200 to 300 lumens per square metre, so 1,000 to 1,500 lumens for 5 m² with the mirror lights included. A round opal glass bathroom ceiling light of 25 to 40 cm, with a GX53 LED supplied or two E27 bulbs, does the job.
Switch, fitting and care
Ordinary switches and sockets stay out of zones 0, 1 and 2. In a British bathroom that means a ceiling pull-cord or a switch outside the door, and no socket apart from a shaver unit within 3 m of zone 1. A wall light with its own pull-cord also belongs outside the zones. A Class II wall light, with the double square on its product page, connects with two wires and no earth. Unless marked as supplied, the bulb is extra. Chrome, on nearly two-thirds of the models, shows limescale; a dry cloth after the shower deals with it.
If you are unsure which zone a position falls in, ask an electrician to check it before you drill. Our guides on choosing a bathroom wall light and on a well-lit bathroom go further than this page.
To check an IP rating or a protection class before you order, call +33 1 84 20 32 51, Monday to Friday, 8am to 5pm UK time; delivery is free in the UK and the European Union, with 30 days to change your mind.